Thermaltake V-Tubler PETG Tube 5/8” (16mm) OD 1000mm 4 Pack
Thermaltake introduces the V-Tubler PETG solid tubing for custom PC water cooling
configurations. Manufactured from premium PETG, the V-Tubler rigid tubing allows users to
route the tubes runs exactly to their heart’s content. Designed with 5/8” (16mm) OD PETG
tube adapter fittings, give users better mounting, easier fitting, and ideal flow. Choose
from: 500mm and 1000mm to make your system a showcase for all to see with the Thermaltake
V-Tubler water tubing.
Tt LCS Certified
Tt LCS Certified is a Thermaltake exclusive certification
applied only to products that pass the design and hardcore enthusiasts standards that a true
LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake
can indicate to all power users which chassis have been tested to be best compatible with
extreme liquid cooling configurations, ensuring you get the best performance from the best
features and fitment.
100% PETG Material
Made in Taiwan, the V-Tubler PETG Tube is constructed from
superior PETG material which is reliable, non-toxic, and substance free. Thicker walls
ensure safe operation, enabling the users to make the straightest run as well as tightest
bends without the need of excessive compression fittings and 90 degree angle rotaries.
Working temperature ranges from -4℉ (-20℃) to 143.6℉ (62℃).
- Outer Diameter: 5/8” (16mm)
- Inner Diameter: 12mm
- Length: 1000mm*4
Remarkable Expansion
Designed for use with 5/8” (16mm) OD PETG tube adapter
fittings, V-Tubler PETG Tube is pre cut into retail coils of four 1000mm lengths, allowing
enthusiasts to build up aesthetically-superior water cooling systems by allocating the
radiators to each particular component and incorporating externally-modular upgrades for
their chassis.
*Coolant operating temperature exceeds 50℃/122°F may potentially affect the PETG tube.
*Thermaltake V-Tubler PETG Tube Series is recommended for use with the Pacific Temperature
Sensor.
Cautions
Thermaltake recommends the following steps to be taken
before using the Pacific series radiators and water blocks
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop
setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
Cautions
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant; it may harm your loop and reduce performance.
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse, and dry them to ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup:
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing corrosion in the entire cooling system – copper, brass, nickel, aluminum, and steel.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushes the coolant into the loop.
- DO NOT let the pump run dry; turn off the power immediately if there is no liquid entering the pump.
- Fill the reservoir to the top to prevent air from entering the pump.
- If necessary, tilt the system slightly from side to side to bleed air out of the loop.
- Place some paper towels under fittings and joining points to check for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed air out of the loop.
- Before starting, flush your system correctly to prevent any coolant or unwanted particles from sticking to your tubes, radiators, and other cooling components.
- Note that coolant might fade over time.
| P/N | CL-W116-PL16TR-A |
|---|---|
| MATERIALE | PETG |
| COLORE | Transparent |
